top of page

Free Shipping Over £150 Subject to T&C's

Untitled design (5)_1769099439.png_width=2400&optimize=medium.png

Fire Rated Downlights: A UK Buying Guide

4 days ago
4 min read

Updated: 3 days ago

Fire Rated Downlights

One small hole in your ceiling can change how fast a fire spreads. Every downlight needs that hole. In a two-storey house, your ceiling is part of a floor that must resist fire for 30 minutes. Without protection, you could lose that precious escape time.


Fire rated downlights fix this by sealing the hole. Choose them with three checks: your ceiling's fire rating, your room's IP rating, and how many lights your space needs. Below, you'll find tables, examples and a checklist for bathrooms, loft conversions and refurbishments.


6 Steps to Choose Fire Rated Downlights for Your Home Ceiling


To buy the right fire-rated downlights, you need to follow six steps. Match the fire rating to your ceiling and the IP rating to your room. Then choose the type and number of lights, check your insulation and loft space, and plan the wiring. The tables below give you a quick view of each step.


Step 1: Match the Fire Rating to Your Ceiling


Fire rated downlights are tested for 30, 60, or 90 minutes. Pick one that matches the ceiling it goes into.


Building type

Typical ceiling rating

Two or three-storey house

30 minutes

Four-storey house

60 minutes

Taller residential building

90 minutes or more


These are typical figures only. Always check the product page for the exact rating before you buy.


Step 2: Choose the Right IP Rating


The IP rating shows how well a light handles water. In your bathroom, BS 7671 splits the room into zones.


Bathroom zone

Where it is

Minimum IP rating

Zone 1

Above the bath or shower, up to 2.25m

IPX4

Zone 2

Up to 0.6m around zone 1, plus above 2.25m

IPX4

Outside zones

The rest of the room

No set minimum


Many people choose IP65 above a shower for extra protection.

Example: A light right above your shower works best as an IP65 fire rated fitting. A light across the room can have a lower rating.


Step 3: Pick the Type of Downlight


Think about how you want your light to behave.


  • Fixed: points straight down, ideal for hallways and bedrooms

  • Tilt: angles towards a wall, worktop or feature

  • IP65: sealed for bathrooms and other damp rooms


You also choose between a GU10 fitting and an integrated LED. GU10 fittings take replaceable bulbs, so you can swap one in seconds. Our range of GU10 lamps covers warm white, cool white and daylight.


At Ghir Electrical Supplies Ltd, our fire rated downlights come in white, satin nickel and polished chrome. You can compare fixed, tilt and IP65 versions on one page.


Step 4: Work Out How Many You Need


There is no single legal number, so use brightness instead. Multiply your room size by the lumens per square metre. Then divide by the lumens in each lamp.


A typical 5W GU10 LED gives around 450 lumens. Check your lamp's label for the real figure.


Room

Lumens per m²

Example size

Lights needed

Hallway

100

6 m²

2

Bedroom

150

12 m²

4

Living room

150

20 m²

7

Bathroom

300

4 m²

3

Kitchen

300

12 m²

8


Example: Your bathroom is 4 m². Multiply by 300 to get 1,200 lumens. Divide by 450, and you need about three lights.


These are rough planning figures, not rules. Space the lights evenly and round up.


Step 5: Check Insulation and Loft Space


Heat can build up around a light if it is covered. Some downlights are safe to cover with insulation. Others need clear space around them.


  • Check the product details for "insulation coverable"

  • Never cover a light unless the maker says it is safe

  • Leave the clearances in the instructions

  • In a loft conversion, plan for the fire rating of the new floor too


If your ceiling doesn't need a fire rating, you can browse our downlight range for other styles.


Step 6: Plan the Wiring and Installation


New lights add load to your circuits. If you're rewiring or extending, read our guide on how to choose the right consumer unit for your home.


Always use a qualified electrician for the fitting. They follow the maker's instructions. They also restore your ceiling's fire resistance after cutting the holes.


Your Quick Checklist Before You Buy


  1. Which fire rating does your ceiling need: 30, 60 or 90 minutes?

  2. Which bathroom zone is the light in, and what IP rating does it need?

  3. Do you want fixed or tilt?

  4. Do you want GU10 or integrated LED?

  5. Is the light safe to cover with insulation?

  6. How many lights does your room need?


FAQs About Fire Rated Downlights


Do I need fire rated downlights? 


You usually do when your ceiling sits under another floor. That includes two-storey houses, flats and loft conversions.


What is the difference between fire rated and IP rated downlights? 


Fire rating protects your ceiling from fire. IP rating protects the light from dust and water. Bathrooms often need both.


How many downlights do I need per room? 


It depends on brightness. A 12 m² bedroom needs around four lights at 450 lumens each.


Can you cover fire rated downlights with insulation? 


Only if the maker says so. Check for "insulation coverable" on the product details.


Which fire rating do I need: 30, 60 or 90 minutes? 


Match it to your ceiling. Most two- or three-storey houses need 30 minutes.


Do fire rated downlights need an electrician?


Yes, if you're not confident working with electrics. A qualified electrician fits them safely and restores your ceiling's fire resistance.


Choose Your Fire Rated Downlights With Confidence


You now know what to check: fire rating, IP rating, type, quantity, and insulation. 

Browse our fire rated downlights and pick the fittings that suit your project.



 
 
 

Comments


bottom of page